Setting up a new shower unit 80055

Installing a New Shower Unit

An effective shower installation requires careful planning and a great deal of work. For the most part, you will require to do 3 kinds of tasks: framing walls, installing the pipes, and finishing walls.

Preparation

Firstly, you need to choose the type of shower that you want to install. It is important to determine whether the picked shower is capable of managing particular systems and can regulate a safe level of water through the boiler. Many shower units nowadays are developed to be flexible to various water pressures (such as kept hot water and cold mains).

It is also essential to consider the water pressure and the preparation of the piping and drainage for the shower

Different Types of Shower Units

Push-on Mixer: The hose pipe and spray parts of the push-on mixer shower system can be connected to the bath tap as per your requirement, and the water temperature level can be adjusted via the taps. Push-on mixers are low-cost and exceptionally simple to install. Nevertheless, although the pipe connection is simple, it is easily removed. Furthermore, it is bothersome to change the temperature level.

Bath/ Shower Mixer: The hose pipe and spray of this kind of shower are combined with a bath mixer tap, and the temperature can be changed through the bath taps. It is a very inexpensive alternative and no additional plumbing is included. However, the bath/shower mixers also suffer from inconvenient temperature level control options.

Manual Mixer: The hose and spray of a manual mixer shower system are a part of the wall system and the hot and cold water supplies are linked to a single valve The temperature level and pressure of the water are controlled through either one or a variety of knobs (in more costly showers). Although temperature control is much easier in manual mixer types, they are more expensive than the formerly pointed out mixers. They likewise require extra plumbing of cold and hot supply of water pipes.

Thermostatic Mixer: The pipe and spray of this shower type belong of the wall system and the hot and cold water supplies are linked to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to prevent it from becoming too hot. Among the most significant advantages of a thermostatic mixer shower type includes hassle-free temperature level control. Nevertheless, it is the most pricey of the different mixer alternatives.

Power Shower: A power shower is a single system including a powerful electrical pump that is capable of altering both the water pressure and temperature. This kind of shower can be fitted if there is water supply from a cold water cistern and a warm water cylinder. A power shower makes the change of both pressure and temperature simple. On the other hand, it disagrees for water warmed directly by the shower or where the water is provided by a combination boiler under mains pressure.

Electric Shower: An electric shower is plumbed into a mains cold water supply and it heats the water electrically. It is very important to note that for this shower type to be installed, the mains pressure requires to be at least 0.7 kg/sq cm (10lb/sq in). The system enables the temperature level and pressure to be changed through a knob. Designs with temperature level stabilisers are much better as they stay untouched by other taps in other places in use within the home. A major downside of electrical showers is that the control knob only allows for the option of high temperatures at less pressure, or lower temperatures at a higher pressure. This is problematic in the winter when the spray is often weak and the mains water is colder. However, this problem is dealt with in some models which are offered with a winter/summer setting.

Method

Depending on the type of shower you wish to install, the shower head should either be fitted in order to prevent its contact with the water in the bath below or the base tray, or it needs to have a check valve.

Before starting, it is suggested to mark the positions of the shower head and control, and to prepare the pipe-work involved. Furthermore, the drain system to remove the drainage will need to be prepared. Both positions of the cable television path and the shower switch will likewise require to be considered if an instantaneous or electric shower unit is being installed.

Use the instruction guide offered with the shower unit to fit the shower control.

Before fitting the pipes that will provide the water to the shower system, it is essential to cut off the water system. 24/7 plumbing service In order to protect the pipelines, they need to be provided a water resistant covering and likewise fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the overall look.

Fit the base tray, shower head, and fittings.

Connect the main shower control to the pipelines that will be providing the water (This may need a female screw thread adapter).

Reconnect the water supply and test the pipes for any leaks, as some may need tightening.

If you are installing an electrical shower, remember to switch off the electrical power supply before making any electrical connections. As soon as these connections have actually been made (there ought to be assistance within the instruction manual), the power supply can be switched back local best plumber on.

Adjusting Water Pressure to Fit Your Shower

The cold water reservoir can be lifted to a higher height (in some cases as low as 150mm (6inches)) by fitting a strong wooden assistance below it-- perhaps composed of struts and blockboards. If you pick this option, the primary and distribution pipes will likewise need to be raised to fulfill the new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is chosen, it should be connected into the power supply in order to operate.

Piping and Drainage

It is best to use 15mm size supply pipes, and make the go to the shower as short and straight as possible so as to keep maximum pressure and minimise heat loss. In addition, by minimising the use of elbows for pipe corners, you can decrease the resistance in the flow of the supply of water. You can achieve this by flexing the pipelines instead.

Most Common Mistakes

# Breaking or ignoring local code restrictions.

# Using pipes that are too small.

# Attaching copper to galvanized without using a brass or dielectric fitting between the two.

# Not utilizing tape or pipe substance at threaded joints.

# Not leveling your components when setting up them.

# Not installing an air space filling for fixtures.

# Cutting supply stub outs too brief to install the shutoff valves onto after the finished wall remains in place.

# Not correctly aligning tubing into fittings or stop valves. (Requiring the nut onto the compression ring at an angle when the tubing is at an angle will cause a leakage.)

# When turning the water back on in your house, constantly run the outside hose valve or flush your toilets to bleed dirt and air from the lines. This debris can cause issues in your sink faucets and other pipes trim.