Installing a new shower system 89064

Installing a New Shower Unit

A successful shower installation needs mindful planning and a great deal of work. For the most part, you will need to do 3 kinds of tasks: framing walls, installing the plumbing, and finishing walls.

Preparation

Firstly, you should select the type of shower that you wish to install. It is essential to determine whether the picked shower can managing particular systems and can manage a safe level of water Cranbourne plumbing experts through the boiler. Most shower units nowadays are developed to be flexible to various water pressures (such as stored warm water and cold mains).

It is likewise important to take into consideration the water pressure and the preparation of the piping and drain for the shower

Different Kinds of Shower Units

Push-on Mixer: The pipe and spray parts of the push-on mixer shower unit can be connected to the bath tap as per your requirement, and the water temperature level can be changed through the taps. Push-on mixers are inexpensive and very basic to install. Nevertheless, although the hose pipe connection is easy, it is quickly dislodged. Furthermore, it is inconvenient to adjust the temperature.

Bath/ Shower Mixer: The hose and spray of this type of shower are combined with a bath mixer tap, and the temperature can be adjusted through the bath taps. It is a very low-cost choice and no additional plumbing is involved. Nevertheless, the bath/shower mixers also experience inconvenient temperature control alternatives.

Manual Mixer: The tube and spray of local plumber services a manual mixer shower unit are a part of the wall system and the cold and hot water materials are linked to a single valve The temperature and pressure of the water are controlled through either one or a variety of knobs (in more pricey showers). Although temperature level control best plumber Mount Martha is a lot easier in manual mixer types, they are more expensive than the formerly discussed mixers. They likewise require extra plumbing of hot and cold water system pipes.

Thermostatic Mixer: The hose pipe and spray of this shower type belong of the wall system and the hot and cold water materials are linked to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to prevent it from ending up being too hot. Among the biggest advantages of a thermostatic mixer shower type includes hassle-free temperature control. However, it is the most costly of the different mixer alternatives.

Power Shower: A power shower is a single unit including a powerful electrical pump that can altering both the water pressure and temperature. This type of shower can be fitted if there is water supply from a cold water tank and a warm water cylinder. A power shower makes the adjustment of both pressure and temperature level simple. On the other hand, it is unsuitable for water warmed directly by the shower or where the water is supplied by a combination boiler under mains pressure.

Electric Shower: An electric shower is plumbed into a mains cold water supply and it warms the water electrically. It is important to keep in mind that for this shower type to be installed, the mains pressure requires to be at least 0.7 kg/sq cm (10lb/sq in). The unit allows the temperature level and pressure to be changed by means of a knob. Models with temperature level stabilisers are much better as they stay unaffected by other taps somewhere else in usage within the home. A major disadvantage of electric showers is that the control knob just enables the option of heats at less pressure, or lower temperatures trusted plumber Baxter at a greater pressure. This is bothersome in the winter when the spray is frequently weak and the mains water is colder. Nevertheless, this problem is dealt with in some models which are readily available with a winter/summer setting.

Method

Depending on the kind of shower you want to install, the shower head must either be fitted in order to prevent its contact with the water in the bath below or the base tray, or it should have a check valve.

Before starting, it is advisable to mark the positions of the shower head and control, and to prepare the pipe-work involved. In addition, the drainage system to remove the waste water will need to be planned. Both positions of the cable television route and the shower switch will also need to be considered if a rapid or electric shower system is being installed.

Use the guideline guide supplied with the shower unit to fit the shower control.

Before fitting the pipelines that will provide the water to the shower system, it is essential to cut off the water system. In order to secure the pipelines, they must be provided a waterproof covering and likewise fitted with separating valves. The pipelines can then be buried into the wall and plastered over to neaten the total look.

Fit the base tray, shower head, and fittings.

Connect the main shower control to the pipelines that will be supplying the water (This may require a female screw thread adapter).

Reconnect the supply of water and test the pipelines for any leakages, as some might need tightening.

If you are setting up an electrical shower, remember to switch off the electricity supply before making any electrical connections. When these connections have actually been made (there ought to be guidance within the user's manual), the power supply can be switched back on.

Adjusting Water Pressure to Match Your Shower

The cold water reservoir can be raised to a higher height (often as low as 150mm (6inches)) by fitting a strong wooden support underneath it-- possibly composed of struts and blockboards. If you select this alternative, the main and distribution pipelines will also have to be raised to satisfy the new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is selected, it must be connected into the power supply in order to operate.

Piping and Drainage

It is best to utilize 15mm size supply pipes, and make the runs to the shower as brief and straight as possible so as to preserve maximum pressure and minimise heat loss. Additionally, by reducing making use of elbows for pipeline corners, you can decrease the resistance in the circulation of the supply of water. You can achieve this by flexing the pipelines instead.

Most Common Mistakes

# Breaching or disregarding local code restrictions.

# Utilizing pipes that are too small.

# Attaching copper to galvanized without utilizing a brass or dielectric fitting between the two.

# Not utilizing tape or pipe compound at threaded joints.

# Not leveling your fixtures when installing them.

# Not setting up an air gap filling for fixtures.

# Cutting supply stub outs too short to install the shutoff valves onto after the ended up wall remains in place.

# Not appropriately aligning tubing into fittings or stop valves. (Requiring the nut onto the compression ring at an angle when the tubing is at an angle will trigger a leakage.)

# When turning the water back on in your house, constantly run the outdoors tube valve or flush your toilets to bleed dirt and air from the lines. This particles can cause problems in your sink faucets and other plumbing trim.