Installing a new shower system 30150

Installing a New Shower Unit

An effective shower installation needs mindful planning and a great deal of work. For the most part, you will require to do three kinds of jobs: framing walls, setting up the plumbing, and ending up walls.

Preparation

Firstly, you should best plumber in Mornington pick the type of shower that you wish to install. It is very important to ascertain whether the picked shower is capable of handling certain systems and can control a safe level of water through the boiler. The majority of shower units nowadays are created to be versatile to various water pressures (such as stored hot water and cold mains).

It is likewise crucial to take into consideration the water pressure and the preparation of the piping and drain for the shower

Different Types of Shower Units

Push-on Mixer: The pipe and spray parts of the push-on mixer shower unit can be linked to the bath tap according to your requirement, and the water temperature level can be adjusted via the taps. Push-on mixers are low-cost and very easy to install. However, although the pipe connection is simple, it is quickly removed. Additionally, it is bothersome to change the temperature level.

Bath/ Shower Mixer: The pipe and spray of this type of shower are combined with a bath mixer tap, and the temperature level can be adjusted through the bath taps. It is a very cheap choice and no additional pipes is involved. However, the bath/shower mixers also experience troublesome temperature control alternatives.

Manual Mixer: The hose and spray of a manual mixer shower system are a part of the wall system and the hot and cold water supplies are linked to a single valve The temperature and pressure of the water are controlled through either one or a range of knobs (in more pricey showers). Although temperature level control is much easier in manual mixer types, they are more expensive than the previously pointed out mixers. They likewise need additional pipes of hot and cold water system pipes.

Thermostatic Mixer: The hose and spray of this shower type belong of the wall system and the cold and hot water supplies are linked to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to avoid it from becoming too hot. One reliable plumber in Mount Martha of the most significant advantages of a thermostatic mixer shower type includes hassle-free temperature level control. Nevertheless, it is the most pricey of the different mixer alternatives.

Power Shower: A power shower is a single system containing a powerful electrical pump that can altering both the water pressure and temperature. This kind of shower can be fitted if there is water supply from a cold water cistern and a warm water cylinder. A power shower makes the modification of both pressure and temperature level easy. On the other hand, it is unsuitable for water warmed straight by the shower or where the water is provided by a mix boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and it heats up the water electrically. It is important to keep in mind that for this shower type to be installed, the mains pressure needs to be at least 0.7 kg/sq cm (10lb/sq in). The system allows the temperature level and pressure to be changed through a knob. Models with temperature level stabilisers are better as they remain unaffected by other taps somewhere else in usage within the home. A major disadvantage of electric showers is that the control knob only permits the alternative of heats at less pressure, or lower temperature levels at a higher pressure. This is troublesome in the winter when the spray is often weak and the mains water is colder. However, this issue is tackled in some models which are offered with a winter/summer setting.

Method

Depending on the kind of shower you wish to install, the shower head need to either be fitted in order to avoid its contact with the water in the bath listed below or the base tray, or it needs to have a check valve.

Before starting, it is recommended to mark the positions of the shower head and control, and to plan the pipe-work involved. Additionally, the drain system to get rid of the drainage will require to be planned. Both positions of the cable television route and the shower switch will likewise require to be thought about if an instantaneous or electrical shower unit is being installed.

Use the direction guide supplied with the shower unit to fit the shower control.

Before fitting the pipelines that will supply the water to the local Hastings plumber shower system, it is very important to cut off the supply of water. In order to safeguard the pipelines, they must be provided a waterproof covering and also fitted with isolating valves. The pipes can then be buried into the wall and plastered over to neaten the general look.

Fit the base tray, shower head, and fittings.

Connect the main shower control to the pipelines that will be supplying the water (This might need a female screw thread adapter).

Reconnect the water system and test the pipelines for any leaks, as some might require tightening.

If you are setting up an electrical shower, keep in mind to switch off the electrical energy supply before making any electrical connections. Once these connections have been made (there should be guidance within the instruction manual), the power supply can be switched back on.

Adjusting Water Pressure to Suit Your Shower

The cold water tank can be raised to a greater height (in some cases as little as 150mm (6inches)) by fitting a strong wood assistance below it-- perhaps composed of struts and blockboards. If you pick this choice, the primary and circulation pipes will likewise need to be raised to meet the new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is chosen, it needs to be connected into the power supply in order to operate.

Piping and Drainage

It is best to use 15mm diameter supply pipes, and make the go to the shower as brief and straight as possible so as to preserve maximum pressure and minimise heat loss. Additionally, by minimising using elbows for pipe corners, you can decrease the resistance in the circulation of the supply of water. You can accomplish this by flexing the pipes instead.

Most Common Mistakes

# Breaching or overlooking regional code restrictions.

# Using pipelines that are too small.

# Attaching copper to galvanized without using a brass or dielectric fitting between the two.

# Not using tape or pipe compound at threaded joints.

# Not leveling your fixtures when installing them.

# Not setting up an air space filling for fixtures.

# Cutting supply stub outs too short to set up the shutoff valves onto after the completed wall remains in place.

# Not properly aligning tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leak.)

# When turning the water back on in your house, constantly run the outdoors tube valve or flush your toilets to bleed dirt and air from the lines. This debris can cause issues in your sink faucets and other plumbing trim.